Home > Black Screen > Black And Blank Screen After Update On G550 With W.

Black And Blank Screen After Update On G550 With W.


If so, we'll be repeating the Intel issue we had with > Jaunty. Either FC4T1 i386 or x86-64 on 2nd disk Clean install of FC4T1 (i386 or x86-64) on Shuttle Athlon64 machine both show the same problem. The machine is superficially very usable but I assume I will have problems at some stage !! I am logged in via my jaunty live-cd. http://evendirectory.com/black-screen/black-screen-of-doom-but-booted-to-login-screen-no-cursor-just-blank.html

The fifth command restarts your Mac. It apparently still is on my hardware at least (Dell GX60, Intel 82845G/GL). wipnme February 25, 2012 | Hello, I have a HP Pavillion DV6000 When I push the power button, the LED blue lights turn on, the dvd drive make noise and hd but then lost video again.Getting ready to do again but wondering if flux may make it work even longer.Please let me know as I've got it apart and am ready to https://forums.lenovo.com/t5/Lenovo-B-and-G-Series-Notebooks/Black-and-blank-screen-after-update-on-G550-with-Windows-8-1/td-p/3437484

Lenovo Ideapad Black Screen On Startup

I am happy enough with the 640 x 480 console, but I have a large monitor that I do not use as I could (and like). Bad connection between the video cable and inverter board. 2. This is just a guess.

Carlos December 13, 2011 | Thanks a lot for sharing this info. The video is sometimes a jumbled mess and other times there's no video at all. victory September 25, 2011 | pls i need the link to the laptop disassembly procedure manual. Lenovo Black Screen Windows 10 Which one do I need to cook, or shall I just do both?

I guess it hasn't been fixed completely. Lenovo Laptop Turns On But Screen Is Black I don't know if this is true for your Acer Aspire 4551 laptop but on some laptops the cooling fan works only for a few seconds on startup and later it I discovered that the HDMI port still worked, even though the laptop screen did not. http://www.tomsguide.com/answers/id-3051432/lenovo-laptop-turns-black-screen.html John Austin, is currently still experiencing the same problem they had when they added a comment or added themselves to CC, pay close attention to this next statement very carefully: YOU

Typing 'fsck -y /dev/sda1' followed by enter doesn't do anything and hdd light does not blink. Lenovo Black Screen After Login I fixed a Compaq Presario V6000 in July 2012 with the oven trick. When the dv2000 died again I had this one laying around in my store from a customer that didn't want it any more so I didn't bother repairing it a second Now when I start my laptop, I hear the fan starting for 2 sec and then nothing more happend.

Lenovo Laptop Turns On But Screen Is Black

Take care! https://answers.microsoft.com/en-us/windows/forum/windows_10-windows_install/black-screen-after-updating-to-windows-10/ef8c1c21-a156-4d15-8b18-51cc2b1ae4d5 Copying libvgahw.a from xorg-x11-6.8.2-1.FC3.13 solves all issues. Lenovo Ideapad Black Screen On Startup summary: - screen powers off during fsck - fbcon loaded too late?+ fbcon loading a mystery (screen powers off) Changed in sysvinit (Ubuntu): importance: Undecided → High Rick Spencer (rick-rickspencer3) wrote Lenovo Laptop Black Screen With Cursor Control-Alt-F1-6 terminals do not have a green border and are visable but the characters are corrupt/incorrect/unreadable !!!!

Bad air flow in the heat exchanger or hair fibers of hypereutectic solder that shorted it out. this contact form If FC4 xorg rebuilt unmodified (at source level) on FC3 works ok on FC3, then it could be a variety of things causing the FC4 problem, some of which might be: The power of the heat gun was set up to get the solder in ball on a coin after 30sec at 1″ distance. so when reheating, the heat should be applied to the four sides and not the center. Lenovo Black Screen Of Death

cj2600 May 3, 2012 | @ Connery Johnson, I’m a little confused… Do I apply the liquid flux underneath the chipset, and then remove and put new thermal grease on top Test your laptop with another AC adapter. 2. The only thing still missing is when I shut down the computer there are no messages indicating processeses being shut down, etc. have a peek here mosuto June 17, 2011 | Thx for advice, i failed with my try some parts close to VGA chip falled when i tryed to remove the foil tejas June 29, 2011

Coz I am wondering how I can determine the time I need to heat up the chip. I Turned My Laptop On And The Screen Is Black Comment 40 Luis 2005-06-17 18:48:54 UTC Sorry for the previous incomplete message. K cj2600 October 24, 2011 | @ Mac, This should not be try unless you are prepared to buy a new computer if it fails.

khan February 25, 2011 | I repaired an HP dv6000's GPU about a month ago using foil and pennies.

Thanks. I was using live 2009-09-27, network now working. It doesn't look like this problem is MGA-only... Lenovo Black Screen Windows 7 at what point do you apply it, and if its when you mention it in your post… why would there be a gap for the flux to seep through??

cj2600 February 2, 2012 | @ mike, my pavillio DV9000 don’t want to turn on? Then I'd like to figure out how we can make fbcon automatically loaded when we need it *properly*, rather than putting a hack in. No green border or green screen anywhere either. Check This Out Any suggestions would be very much appreciated.

My hardware is an ASUS EeePC 4G, which uses the Intel Driver mentioned above. I hope that all the problems have been recognised !!!! At other times, the Blue Screen Of Death (showing the generic hardware failure code) might occur. They're *just* fonts, no code.

hewbert (josh-hewbert) wrote on 2009-10-03: #49 Just wanted to add a "me too". The developers are very busy and don't have time to keep checking back on comments for bugs that have already been marked as fixed. To help determine which of these might be the case, try installing the FC4 kernel, and any direct dependancies it has into FC3 without changing xorg-x11 now. Replacing the libvgahw.a fixed the problem for me too.

Lasted about 6 or 9 months then went again so pretty good result. Is there any way to avoid this to happen again? If the hardware is older, and the alternative to fixing it is to throw it away, you should try to reflow the solder connections on the chip. […] Ahsan February 24, It works for 2/3 days then again same problem….

Olli Helenius (liff) wrote on 2009-10-02: #47 Wondering if my problem is related to this: I get a black screen (monitor goes to standby) when booting the livecd/installer. Comment 21 Per Starbäck 2005-04-25 03:50:35 UTC (In reply to comment #12) > Created an attachment (id=2486) [edit] > Xorg.0.log for Mystique (mga1064sg) > Quoting the log file: ---------------------------------- Symbol XAAGetCachePlanarMonoStipple